A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

- A -

Above Grade: The portion of a building that is above ground level.

Acre: 43,560 square feet.

A/C: An abbreviation for air conditioner or air conditioning.

A/C Circuit (Alternating Current): The flow of current through a conductor first in one direction then in reverse. It is used exclusively in residential and commercial wiring because it provides greater flexibility in voltage selection and simplicity of equipment design.

Accelerator: Any material added to stucco, plaster or mortar which speeds up the natural set.

A/C Condenser: The condenser is the outside fan unit of the Air Conditioning system. It removes the heat from the Freon gas and turns the gas back into a liquid and pumps the liquid back to the coil in the furnace.

A/C Disconnect: The main electrical ON-OFF switch near the A/C Condenser.

Acrylic Knockdown (AKD): Finish applied to a concrete floor surface. Typically applied on porch floors and decking surrounding swimming pools. The concrete deck receives a textured finish. It then receives an acrylic elastic type paint or coating applied over the textured finish. It can be easily recoated or painted later which makes it appear new again. Any exterior floor area in Florida should be hosed down weekly to keep mildew at bay.

Adhesion: The property of a coating or sealant to bond to the surface to which it is applied.

Adhesive Failure: Loss of bond of a coating or sealant from the surface to which it is applied.

Aerator: The round screened screw-on tip of a sink spout. It mixes water and air for a smooth flow.

Aggregate: Crushed stone, slag or water-worn gravel that comes in a wide range of sizes that is used to surface built-up roofs.

Air Conditioned Living Area: The square footage of the area that is air conditioned in a home. Areas such as garage, porches, non air conditioned attic storage areas, etc. are not included in this measurement. When cost per square foot is considered the cost of the home is typically divided by the square footage of Air Conditioned Living Area. Large amounts of non air conditioned area canhave a huge impact on the cost per square foot of a home.

Air-Dried Lumber: Lumber that has been piled in yards or sheds for any length of time. For the United States as a whole, the minimum moisture content of thoroughly air dried lumber is 12 to 15 percent and the average is somewhat higher. In the South, air dried lumber may be no lower than 19 percent.

Air Duct: Ducts, usually made of sheet metal, that carry cooled air to all rooms.

Air Filters: Adhesive filters made of metal or various fibers that are coated with adhesive liquid to which the particles of lint and dust adhere. These filters will remove as much as 90% of the dirt if they do not become clogged. The more common filters are of the throwaway or disposable type.

Air Infiltration: The amount of air leaking in and out of a building through cracks in walls, windows and doors.

Airway: A space between roof insulation and roof boards for movement of air.

Alligatoring: A condition of paint or aged asphalt brought about by the loss of volatile oils and the oxidation caused by solar radiation. Coarse checking pattern characterized by a slipping of the new paint coating over the old coating to the extent that the old coating can be seen through the fissures. "Alligatoring" produces a pattern of cracks resembling an alligator hide and is ultimately the result of the limited tolerance of paint or asphalt to thermal expansion or contraction.

Allowances: In the specifications for the construction of a home typically numerous items are called allowances. They are typically decorator items such as cabinets, tile, wallpaper, carpet, landscaping, etc. The Builder will base the price of the home including allowances for the items agreed to as allowance items. Depending upon the choices the Buyer makes they will receive a credit if their choice is less than the allowance, none if the same as the allowance, or they will be charged the additional amount if their choice cost more than the allowance for that particular item. This is an area that allows many unscrupulous Builders to offer a below market price for a home by reducing the allowances. The Buyers receive many unpleasant surprises when Builders do this throughout the process. It is not at all unusual to find out that the Builder with the higher bid has in fact the lowest cost in the end due to this practice. Protect yourself by doing some research on what you desire for the allowance items vs. the allowance offered.

Aluminum Wire: Conductors made of aluminum for carrying electricity. Aluminum generally is limited to the larger wire sizes. Due to its lower conductivity, aluminum wire smaller than No. 12 is not made. Aluminum is lighter and less expensive than copper but not as good a conductor. It also breaks easily.

AMPS (Amperes): The rate at which electricity flows through a conductor.

Ammeter: Device to measure the current flowing in a circuit

Amortization: A payment plan by which a loan is reduced through monthly payments of principal and interest.

Anchor Bolts: In residential construction, Bolts to secure a wooden sill plate to concrete, or masonry floor or wall. In commercial construction, Bolts which fasten columns, girders or other members to concrete or masonry such as bolts used to anchor sills to masonry foundation.

Angle Iron: A piece of iron that forms a right angle and is used to span openings and support masonry at the openings. In brick veneer, they are used to secure the veneer to the foundation. Also known as shelf angle.

Annealing: In the manufacturing of float glass, it is the process of controlled cooling done in a lehr to prevent residual stresses in the glass. Re-annealing is the process of removing objectionable stresses in glass by re-heating to a suitable temperature followed by controlled cooling.

Annual Percentage Rate (APR): Annual cost of credit over the life of a loan, including interest, service charges, points, loan fees, mortgage insurance, and other items.

Anti-Walk Blocks: Elastomeric blocks that limit lateral glass movement in the glazing channel which may result from thermal, seismic, wind load effects, building movement, and other forces that may apply.

Approach: The area between the sidewalk and the street that leads to a driveway or the transition from the street as you approach a driveway.

Apron: The flat member of the inside trim of a window placed against the wall immediately beneath the stool.

Architect: A tradesman who designs and produces plans for buildings, often overseeing the building process.

Architects Rule: Three-sided ruler with different scales on each side. Also referred to as a "scale."

Architectural Ceilings: Known as tray ceilings or other specially designed ceilings. They are typically designed by the Interior Architectural Designer and not the Architect or Designer of the home.

Areaway: An open subsurface space adjacent to a building used to admit light or air or as a means of access to a basement.

Asphalt: A dark brown to black, highly viscous, hydrocarbon produced from the residue left after the distillation of petroleum. Asphalt is used on roofs and highways as a waterproofing agent. Most native asphalt is a residue from evaporated petroleum. It is insoluble in water but soluble in gave. line when heated. Used widely in building for waterproofing roof coverings of many types, exterior wall coverings, flooring tile, and the like.

Astragal: A molding, attached to one of a pair of swinging doors, against which the other door strikes.

Attic Access: An opening that is placed in the drywalled ceiling of a home providing access to the attic.

Attic Ventilators: In houses, screened opening) provided to ventilate an attic space. They are located in the soffit area as inlet ventilators and in the gable end or along the ridge as outlet ventilators. They can also consist of power-driven fans used as an exhaust system. (See also Louver)

Auger: In carpentry, a wood-boring tool used by a carpenter to bore holes.

Automated lighting control system: A professionally installed system that controls lights in multiple rooms without use of manual switches.

back to top

- B -

Backer Rod: In glazing, a polyethylene or polyurethane foam material installed under compression and used to control sealant joint depth, provide a surface for sealant tooling, serve as a bond breaker to prevent three-sided adhesion, and provide an hour-glass contour of the finished bead.

Backfill: (1) filling in any previously excavated area, i.e., The replacement of excavated earth into a trench around and against a basement foundation. (2) in carpentry, the process of fastening together two pieces of board by gluing blocks of wood in the interior angle.

Backflow: The flow of liquids through irrigation into the pipes of a potable or drinking water supply from any source which is opposite to the intended direction of flow.

Backflow Preventer: A device or means to prevent backflow into the potable water supply.

Backhand: A simple molding sometimes used around the outer edge of plain rectangular casing as a decorative feature.

Backhoe: Self-powered excavation equipment that digs by pulling a boom mounted bucket towards itself. It is used to dig basements and/or footings and to install drainage or sewer systems.

Backsplashes: Wall area between the cabinet countertop and the upper cabinets. This area can have tile, granite, wallpaper, or painted an accent color.

Back Nailing: The practice of nailing roofing felts to the deck under the overlap, in addition to hot mopping, to prevent slippage of felts.

Balloon Framing: In carpentry, the lightest and most economical form of construction, in which the studding and corner plates are set up in continuous lengths from the first floor line or sill to the roof plate to which all floor joists are fastened.

Balusters: Vertical members in a railing used between a top rail and bottom rail or the stair treads. Sometimes referred to as 'pickets' or 'spindles'.

Balustrade: The rail, posts and vertical balusters along the edge of a stairway or elevated walkway.

Banding: Typically refers to exterior veneer of the home. Banding is the trim installed around windows, doors, and other exterior architectural features of the home. It can be made out of stucco, wood, or stone.

Barge Board: A decorative board covering the projecting rafter (fly rafter) of the gable end. At the cornice, this member is a facie board.

Base (or Baseboard): A board placed against the wall around a room next to the floor to finish properly between floor and plaster.

Barometer: Instrument for measuring atmospheric pressure.

Barrel Roof: A roof design, which in cross section is arched.

Base Flashing: The upturned edge of the watertight membrane formed at a roof termination point by the extension of the felts vertically over the cant strip and up the wall for a varying distance where they are secured with mechanical fasteners.

Base Molding: Molding used to trim the upper edge of interior baseboard.

Base Ply: An asphalt-saturated and/or coated felt installed as the first ply with 4 inch laps in a built - up roof system under the following felts which can be installed in a shingle-like fashion.

Base Shoe: Molding used next to the floor on interior base board. Sometimes called a carpet strip.

Batten: Narrow strips of wood used to cover joints or as decorative vertical members over plywood or wide boards.

Bath Accessories: Includes the toilet tissue holder and towel bars. They can be metal or ceramic.

Batten Plate: A formed piece of metal designed to cover the joint between two lengths of metal edge.

Batter Board: One of a pair of horizontal boards nailed to posts set at the corners of an excavation, used to indicate the desired level, also as a fastening for stretched strings to indicate outlines of foundation walls.

Batt Insulation: Strips of insulation, usually fiberglass that fit between studs or other framing.

Bay Window: Any window space projecting outward from the walls of a building, either square or polygonal in plan.

Bead: In glazing, an applied sealant in a joint irrespective of the method of application, such as caulking bead, glazing bead, etc. Also a molding or stop used to hold glass or panels in position.

Beam: Structural support member (steel, concrete, lumber) transversely supporting a load that transfers weight from one location to another.

Bearing Partition: A partition that supports any vertical load in addition to its own weight.

Bearing Wall: A wall that supports any vertical load in addition to its own weight.

Bed or Bedding: In glazing, the bead compound or sealant applied between a light of glass or panel and the stationary stop or sight bar of the sash or frame. It is usually the first bead of compound or sealant to be applied when setting glass or panels.

Bed Molding: A molding in an angle, as between the over hanging cornice, or eaves, of a building and the side walls.

Bell Reducer: In plumbing, a fitting shaped like a bell which has one opening of a smaller diameter used to reduce the size of the pipe in the line, and the opposite opening of larger diameter.

Below Grade: The portion of a building that is below ground level.

Bent Glass: Flat glass that has been shaped while hot into curved shapes.

Bevel: The angle of the front edge of a door usually from 1/8" to 2".

Bevel Siding (or Lap Siding): Wedge-shaped boards used as horizontal siding in a lapped pattern. This siding varies in butt thickness from 1⁄2 to 3⁄4 inch and in widths up to 12 inches. Normally used over some type of sheathing.

Bid Bond: Security posted by a bidder to ensure performance in accordance with a bid.

Bidding: Getting prices from various contractors and/or subcontractors.

Bid Documents: Drawings, details, and specifications for a particular project.

Bi-fold door: Doors that are hinged in the middle for opening in a smaller area than standard swing doors. Often used for closet doors.

Bi-pass doors: Doors that slide by each other and commonly used as closet doors.

Bite: The dimension by which the framing system overlaps the edge of the glazing infill.

Bitumen: Any of various mixtures of hydrocarbons occurring naturally or obtained through the distillation of coal or petroleum. (See Coat Tar Pitch and Asphalt)

Bleeding: A migration of a liquid to the surface of a component or into/onto an adjacent material.

Blind Nailing: Nailing in such a way that the nail heads are not visible on the face of the work—usually at the tongue of matched boards.

Blind Stop: A rectangular molding, usually 3⁄4 by 1 - 3/8 inches or more in width, used in the assembly of a window frame. Serves as a stop for storm and screen or combination windows and to resist air infiltration.

Blister: An enclosed raised spot evident on the surface of a building. They are mainly caused by the expansion of trapped air, water vapor, moisture or other gases.

Blocking: In carpentry, the process of fastening together two pieces of board by gluing or nailing blocks of wood in the interior angle.

Blue Prints: Architectural plans for a building or construction project, which are likely to include floor plans, footing and foundation plans, elevations, plot plans, and various schedules and or details.

Blue Stain: A bluish or grayish discoloration of the sapwood caused the growth of certain mold like fungi on the surface and in the interior of a piece, made possible by the same conditions that favor the growth of other fungi.

Board Foot: In carpentry, the equivalent of a board 1-foot square and 1-inch thick.

Boards: Yard lumber less than two inches thick and two or more inches wide.

Bodied Linseed Oil: Linseed oil that has been thickened in viscosity by suitable processing with heat or chemicals. Bodied oils are obtainable in a great range in viscosity from a little greater than that of raw oil to just short of a jellied condition.

Boiled Linseed Oil: Linseed oil in which enough lead, manganese or cobalt salts have been incorporated to make the oil harden more rapidly when spread in thin coatings.

Bolster: A short horizontal timber or steel beam on top of a column to support and decrease the span of beams or girders.

Bond Breaker: A substance or a tape applied between two adjoining materials to prevent adhesion between them.

Bond Plaster: In addition to gypsum, bond plaster contains 2-5% lime by weight and chemical additives which improve the bond with dense non-porous surfaces such as concrete. It is used as a base coat.

Boston Ridge: A method of applying asphalt or wood shingles at the ridge or at the hips of a roof as a finish.

Bottom chord: The lower or bottom horizontal member of a truss.

Bow: A curve, bend, warping or other deviation from flatness in glass or wood.

Brace: An inclined piece of framing lumber applied to wall or floor to stifled the structure. Often used on walls as temporary bracing until framing has been completed.

Bracing: Ties and rods used for supporting and strengthening various parts of a building used for lateral stability for columns and beams.

Brake Metal: Sheet metal that has been bent to the desired configuration.

Breaker panel: The electrical box that distributes electric power entering the home to each branch circuit (each plug and switch) and composed of circuit breakers.

Brick Veneer: A facing of brick laid against and fastened to sheathing of a frame wall or tile wall construction.

Bridging: Small wood or metal members that are inserted in a diagonal position between the floor joists at midspan to act both as tension and compression members for the purpose of bracing the joists a spreading the action of loads.

Browncoat: The coat of plaster directly beneath the finish coat. In three-coat work, the brown is the second coat.

BTU (British Thermal Unit): The amount of heat energy required to raise the temperature of one pound of water through a change of one degree farenheit.

Bubbling: In glazing, open or closed pockets in a sealant caused by release, production or expansion of gasses.

Buck: Often used in reference to rough frame opening members. Door bucks used in reference to metal door frame.

Builder's Risk Insurance: Insurance coverage on a construction project during construction, including extended coverage that may be added for the contract for the customer's protections.

Building Brick: Brick for building purposes not especially treated for texture or color, formerly called "common brick." It is stronger than face brick.

Building Codes: Local and state ordinances governing the manner in which a home may be constructed or modified.

Building Paper: A general term for papers, felts, and similar sheet materials used in buildings without reference to their properties or uses.

Building Permit: Written authorization from the city, county or other governing regulatory body giving permission to construct or renovate a building. A building permit is specific to the building project described in the application.

Built INS: Can be anywhere in the home. The Built Ins are typically designed by the Interior Architectural Designer. They are normally built into some type of niche specially prepared for the Built in. They are highly personalized and not inexpensive. Normally, the built-ins are finished wood and include TV entertainment centers, Bookcases, Desk, Storage Chest, and much more.

Built-Up Roof: A roofing composed of three to five layers of asphalt felt laminated with coal tar, pitch, or asphalt. The top is finished with crushed slag or gravel. Generally used on flat or low-pitched roofs.

Bullfloat: A tool used to finish and flatten a slab. After screeding, the first stage in the final finish of concrete, smoothes and levels hills and voids left after screeding. Sometimes substituted for darbying. A large flat or tool usually of wood, aluminum or magnesium with a handle.

Bull nose (drywall): Rounded drywall corners.

Butt Joint: The junction where the ends of two timbers or other members meet in a square-cut joint.

Butterfly Roof: A roof assembly, which pitches sharply from either side toward the center.

Buttering: In glazing, application of sealant or compound to the flat surface of some member before placing the member in position, such as the buttering of a removable stop before fastening the stop in place.

Butt Glazing: The installation of glass products where the vertical glass edges are without structural supporting mullions.

Butyl: Type of non-curing and non-skinning sealant made from butylene. Usually used for internal applications.

BX-Armored Cable: A factory assembly of insulated conductors inside a flexible metallic covering. It can be run except where exposed to excessive moisture and should not be run below grade. It must always be grounded and uses its armor as an equipment ground. It is difficult to pull out old wires or insert new ones.

back to top

- C -

Café Grille Hood: Installed on the rear porch over the outdoor grille. They should include a venting system to remove all smoke and odor to the outside through the roof or side wall of the home.

Calcium Chloride: A chemical used to speed up curing of concretve during damp conditions.

Canopy: An overhanging roof.

Cantilever: A projecting structure, such as a beam, that is supported at one end and carries a load at the other end or along its length.

Cant Strip: A beveled support used at the junction of a flat surface and a vertical surface to prevent bends and/or cracking of the roofing membrane at the intersection of the roof deck and wall. Used with a base flashing to minimize breaking of the roofing felts.

Cap: The upper member of a column, pilaster, door cornice, molding, and the like.

Cap Sheets: In roofing, one to four plies of felt bonded and top coated with bitumen that is laid over an existing roof as a treatment for defective roofs.

Cape Chisel: Tool used to clean out mortar joints on brick.

Carbide Bit: Tool used to drill holes in brick or block.

Casement Frames and Sash: Frames of wood or metal enclosing part or all of the sash, which may be opened by means of hinges affixed to the vertical edges.

Casing: Molding of various widths and thicknesses used to trim door and window openings at the jambs.

Cast Stone: Man made material to resemble coral stone or some other type of natural stone. Cast Stone is very expensive. Many times the same look can be accomplished through our stucco artists at a fraction of the cost.

Caulk: (v) The application of sealant to a joint, crack or crevice. (n) A compound used for sealing that has minimum joint movement capability; sometimes called low performance sealant.

C/D Circuit: A circuit where electricity flows in one direction only, at a constant rate.

Cellulose Insulation: Ground up newspaper that is treated with a fire retardant.

Cement: The gray powder that is the 'glue' in concrete. Portland cement. Also, any adhesive.

Cement Mixtures:
Rich: 1 part cement, 2 parts sand, 3 parts coarse aggregate. Used for concrete roads and waterproof structures.

Standard: 1 part cement, 2 parts sand, 4 parts coarse aggregate. Used for reinforced work floors, roofs, columns, arches, tanks, sewers, conduits, etc.

Medium: 1 part cement, 2 1/2 parts sand, 5 parts coarse aggregate. Used for foundations, walls, abutments, piers, etc.

Lean: 1 part cement, 3 parts sand, 6 parts coarse aggregate. Used for all mass concrete work, large foundations, backing for stone masonry, etc. Mixtures are always listed Cement to Sand to Aggregate

Cement Types:
Type I Normal is a general purpose cement suitable for practically all uses in residential construction but should not be used where it will be in contact with high sulfate soils or be subject to excessive temperatures during curing.

Type II Moderate is used where precaution against moderate sulfate attack is important, as in drainage structures where sulfate concentrations in groundwater's are higher than normal.

Type III High Early Strength is used when high strengths are desired at very early periods, usually a week or less. It is used when it is desirable to remove forms as soon as possible or to put the concrete into service quickly.

Type IV Low Heat is a special cement for use where the amount and rate of heat generated during curing must be kept to a minimum. The development of strength is slow and is intended in large masses of concrete such as dams.

Type V Sulfate Resisting is a special cement intended for use only in construction exposed to severe sulfate action, such as western states having soils of high alkali content.

Ceramic Tile: A man-made or machine-made clay tile used to finish a floor or wall. Generally used in bathtub and shower enclosures and on counter tops.

Certificate of Occupancy: Issued by the County Building Department once the home has passed all of the required inspections by the County building department. This certificate is issued by the local municipality and is required before anyone can occupy and live within the home. It is issued only after the local municipality has made all inspections and all monies and fees have been paid.

CFM (Cubic Feet per Minute): A rating that expresses the amount of air a blower or fan can move. The volume of air (measured in cubic feet) that can pass through an opening in one minute.

Chair Rail: A molding that runs horizontally along the wall at about three to four feet from the ground. In storefront, window wall, or curtain wall systems, a chair rail is an aluminum extrusion applied horizontally to the inside of the system three feet from the floor to create a barrier in floor-to-ceiling glazing applications.

Channel Glazing: The installation of glass products into U-shaped glazing channels. The channels may have fixed stops; however, at least one glazing stop on one edge must be removable.

Checking: Fissures that appear with age in many exterior paint coatings, at first superficial, but which in time may penetrate entirely through the coating. It produces a pattern of surface cracks running in irregular lines. When found in the top pour of an asphalt built-up roof, checking is the preliminary stage of alligatoring.

Checkrails: Meeting rails sufficiently thicker than a window to fill the opening between the top and bottom sash made by the parting stop in the frame of double-hung windows. They are usually beveled.

Chemical Injection Grouting: Leak repair technique usually used below grade in cracks and joints in concrete walls and floors that involves injection of sealant (usually urethane) that reacts with water to form a seal.

Circuit: The path of electrical flow from a power source through an outlet and back to ground.

Circuit Breaker: A device which looks like a switch and is usually located inside the electrical breaker panel or circuit breaker box. It is designed to (1) shut of the power to portions or all of the house and (2) to limit the amount of power flowing through a circuit (measured in amperes). 110 volt household circuits require a fuse or circuit breaker with a rating of 15 or a maximum of 20 amps. 220 volt circuits may be designed for higher amperage loads e.g. a hot water heater may be designed for a 30 amp load and would therefore need a 30 amp fuse or breaker.

Cleat: A wedge-shaped piece (usually of metal) which serves as a support or check. A strip fastened across something to give strength or hold something in position.

CO: An abbreviation for 'Certificate of Occupancy'.

Coal Tar Pitch: A bituminous material, which is a by-product from the coking of coal. It is used as the waterproofing material for tar and gravel built-up roofing.

Coating: A layer of any liquid product spread over a surface for protection.

Cohesive Failure: Internal splitting of a compound resulting from over-stressing of the compound.

Cold air return: The ductwork (and related grills) that carries room air back to the furnace for re-heating.

Cold Applied: Products that can be applied without heating. These are in contrast to products which need to be heated to be applied.

Cold Patch: In roofing, a roof repair done with cold-applied material.

Collar: In roofing, a conical metal cap flashing used in conjunction with vent pipes or stacks usually located several inches above the plane of the roof, for the purpose of shedding water away from the base of the vent.

Collar Beam: In carpentry, a tie that keeps the roof from spreading. They serve to stiffen the roof structure. Connects similar rafters on opposite sides of roof.

Column: In architecture: A perpendicular supporting member, circular or rectangular in section, usually consisting of a base, shaft, and capital. In engineering: A vertical structural compression member which supports loads acting in the direction of its longitudinal axis.

Combination Doors or Windows: Combination doors or windows used over regular openings. They provide winter insulation and summer protection and often have self storing or removable glass and screen inserts. This eliminates the need for handling a different unit each season.

Combustion Air: The duct work installed to bring fresh, outside air to the furnace and/or hot water heater. Normally 2 separate supplies of air are brought in: One high and One low.

Compatible: Two or more substances, which can be mixed or blended without separating, reacting, or affecting either material adversely.

Component: Any one part of an assembly associated with construction.

Composite Board: An insulation board, which has two different insulation types laminated together in 2 or 3 layers.

Compound: A chemical formulation of ingredients used to produce a caulking, elastomeric joint sealant, etc.

Compression Gasket: A gasket designed to function under compression.

Compression Set: The permanent deformation of a material after removal of the compressive stress.

Compressor: A mechanical device that pressurizes a gas in order to turn it into a liquid, thereby allowing heat to be removed or added. A compressor is the main component of conventional heat pumps and air conditioners. In an air conditioning system, the compressor normally sits outside and has a large fan (to remove heat).

Concrete: The mixture of Portland cement, sand, gravel, and water. Used to make garage and basement floors, sidewalks, patios, foundation walls, etc. It is commonly reinforced with steel rods (rebar) or wire screening (mesh).

Concrete Block: A hollow concrete 'brick' often 8-inches x 8-inches x 16-inches in size.

Concrete Plain: Concrete either without reinforcement, or reinforced only for shrinkage or temperature changes.

Condensate Line: The copper pipe that runs from the outside air conditioning condenser to the inside furnace (where the a/c coil is located).

Condensation: The appearance of moisture (water vapor) on the surface of an object caused by warm moist air coming into contact with a colder object. In a building: Beads or drops of water (and frequently frost in extremely cold weather) that accumulate on the inside of the exterior covering of a building when warm, moisture-laden air from the interior reaches a point where the temperature no longer permits the air to sustain the moisture it holds. Use of louvers or attic ventilators will reduce moisture condensation in attics. A vapor barrier under the gypsum lath or dry wall on exposed walls will reduce condensation in them.

Condensing Unit: The outdoor component of a cooling system. It includes a compressor and condensing coil designed to give off heat.

Conditions, Covenants, and Restrictions (CC and R's): The standards that define how a property may be used and the protections the developer makes for the benefit of all owners in a subdivision.

Conductor: In roofing, a pipe for conveying rainwater from the roof gutter to a drain, or from a roof drain to the storm drain; also called a leader, downspout, or downpipe. In electrical contracting, a wire through which a current of electricity flows, better known as an electric wire.

Conduction: The flow of heat from one part of a substance to another part. A piece of iron with one end placed in a fire will soon become warm from end to end, from the transfer of heat by the actual collision of the air molecules.

Conduit: A pipe, usually metal, for protecting and routing electrical wiring.

Construction (Frame): A type of construction in which the structural parts are wood or depend upon a wood frame for support. In codes, if masonry veneer is applied to the exterior walls, the classification of this type of construction is usually unchanged.

Construction Agreement: The contractual agreement between the Buyers and the Builder. This agreement spells out the rights, obligations, and duties between both parties.

Construction Loan: A loan provided by a lending institution specifically to construct or renovate a building.

Construction Specifications: Attached to the Construction Agreement. The specifications cannot be too long. Ours are typically 100 pages or more detailing everything we can think of that has been included with the home as well as anything that is not. This is a very important document. If it is not a substantial size document be very careful.

Control Joint: Tooled, straight grooves made on concrete floors to control where the concrete should crack.

Convection: Currents created by heating air, which then rises and pulls cooler air behind it. Also see radiation.

Cooling Load: The amount of cooling required keeping a building at a specified temperature during the summer, usually 78° F, regardless of outside temperature.

Cooling Tower: A large device mounted on roofs, consisting of many baffles over which water is pumped in order to reduce its temperature.

Coped Joint: See Scribing.

Coping: A construction unit placed at the top of the parapet wall to serve as a cover for the wall.

Copper Pipe Types: Type K has the heaviest or thickest wall and is generally used underground. It has a green stripe. Type L has a medium wall thickness and is most commonly used for water service and for general interior water piping. It has a blue stripe. Type M has a thin wall and many codes permit its use in general water piping installation. It has a red stripe.

Corbel: The triangular, decorative and supporting member that holds a mantel or horizontal shelf.

Corbel Out: To build out one or more courses of brick or stone from the face of a wall, to form a support for timbers.

Core: A small section cut from any material to show internal composition.

Corner Bead: A strip of formed sheet metal, sometimes combined with a strip of metal lath, placed on corners before plastering to reinforce them. Also, a strip of wood finish three-quarters-round or angular placed over a plastered corner for protection.

Corner Boards: Used as trim for the external corners of a house or other frame structure against which the ends of the siding are finished.

Corner Braces: Diagonal braces at the corners of frame structure to stiffen and strengthen the wall.

Cornerite: Metal-mesh lath cut into strips and bent to a right angle. Used in interior corners of walls and ceilings on lath to prevent cracks in plastering.

Cornice: Overhang of a pitched roof, usually consisting of a fascia board, a soffit and appropriate trim moldings.

Cornice Return: That portion of the cornice that returns on the gable end of a house.

Corrosion: The deterioration of metal by chemical or electrochemical reaction resulting from exposure to weathering, moisture, chemicals or other agents or media.

Corrugated: Folded or shaped into parallel ridges or furrows so as to form a symmetrically wavy surface.

Cost Breakdown: A breakdowns of all the anticipated costs on a construction or renovation project.

Counter Flashing: The formed metal secured to a wall, curb, or roof top unit to cover and protect the upper edge of a base flashing and its associated fasteners. This type of flashing is usually used in residential construction on chimneys at the roofline to cover shingle flashing and to prevent moisture entry.

Coupling: In plumbing, a short collar with only inside threads at each end, for receiving the ends of two pipes which are to be fitted and joined together. A right/left coupling is one used to join 2 gas pipes in limited space.

Course: A single layer of brick or stone or other building material.

Cove Molding: A molding with a concave face used as trim or to finish interior corners.

Covenants: Rules usually developed by a builder or developer regarding the physical appearance of buildings in a particular geographic area. Typical covenants address building height, appropriate fencing and landscaping, and the type of exterior material (stucco, brick, stone, siding, etc) that may be used.

Crawl Space: A shallow open area between the floor of a building and the ground, normally enclosed by the foundation wall.

Crazing: A series of hairline cracks in the surface of weathered materials, having a web-like appearance. Also, hairline cracks in pre-finished metals caused by bending or forming (See Brake Metal)

Cricket: A small drainage-diverting roof structure of single or double slope placed at the junction of larger surfaces that meet at an angle, such as above a chimney.

Cross-Bridging: Diagonal bracing between adjacent floor joists, placed near the center of the joist span to prevent joists from twisting.

Crown Molding: A molding used on cornice or wherever an interior angle is to be covered.

Cupola: A small monitor or dome at the peak of a pitched roof.

Curb: A short wall or masonry built above the level of the roof that provides a means of flashing the deck equipment.

Curing: In concrete application, the process in which mortar and concrete harden. The length of time is dependent upon the type of cement, mix proportion, required strength, size and shape of the concrete section, weather and future exposure conditions. The period may be three weeks or longer for lean concrete mixtures used in structures such as dams or it may be only a few days for richer mixes. Favorable curing temperatures range from 50 to 70 degrees fahrenheit. Design strength is achieved in 28 days.

Curing Agent: One part of a multi-part sealant which, when added to the base, will cause the base to change its physical state by chemical reaction between the two parts.

Curtain Wall: A thin wall, supported by the structural steel or concrete frame of the building independent of the wall below. Also a metal (most often aluminum) framing system on the face of a building containing vision glass panels and spandrel panels made of glass, aluminum, or other material.

Cutback: In roofing, basic asphalt or tar which has been "cut back" with solvents and oils so that the material become fluid.

Cut-in Brace: Nominal 2-inch thick members, usually two by four’s, cut in between each stud diagonally.

Cut Off: A piece of roofing membrane consisting of one or more narrow plies of felt usually moped in hot to seal the edge of insulation at the end of a day's work.

back to top

- D -

d: See Penny.

Dado: A rectangular groove across the width of a board or plank. In interior decoration, a special type of wall treatment.

Damper: Valve for controlling airflow. When ordering registers, make sure each supply outlet has a damper so the air flow can be adjusted and turned off. Dampers maybe either manually or automatically operated. Automatic dampers are required for exhaust air ducts.

Dampproofing: A process used on concrete, masonry or stone surfaces to repel water, the main purpose of which is to prevent the coated surface from absorbing rain water while still permitting moisture vapor to escape from the structure. (Moisture vapor readily penetrates coatings of this type.) "Dampproofing" generally applies to surfaces above grade; "waterproofing" generally applies to surfaces below grade.

Darby: A flat tool used to smooth concrete flatwork immediately after screeding. See Bullfloating.

Dead Load: The constant, design-weight (of the roof) and any permanent fixtures attached above or below.

Decay: Disintegration of wood or other substance through the action of fungi.

Deck: An elevated platform. Also commonly used to refer to the above-ground floors in multi-level parking garage.

Deck Paint: An enamel with a high degree of resistance to mechanical wear, designed for use on such surfaces as porch floors.

Deco Drain: Normally found at the intersection of the concrete rear porch and the concrete pool deck. The drain has a perforated top where the water drains into a PVC trough and is then directed to the yard of the home. We use a larger than standard Deco Drain to be sure that no future problems will occur.

Dedicated Circuit: An electrical circuit that serves only one appliance (ie, dishwasher) or a series of electric heaters or smoke detectors.

Deflect: To bend or deform under weight.

Deflection: The amount of bending movement of any part of a structural member perpendicular to the axis of the member under an applied load.

Density: The mass of substance in a unit volume. When expressed in the metric system, it is numerically equal to the specific gravity of the same substance.

Design Pressure: Specified pressure a product is designed to withstand.

Dew Point: Temperature at which vapor condenses from the atmosphere and forms water.

Dimension Lumber: Yard lumber from two inches to, but not including, five inches thick and two or more inches wide. Includes joists, rafters, studs, plank, and small timbers.

Direct Nailing: To nail perpendicular to the initial surface or to the junction of the pieces joined. Also termed face nailing.

Disconnect: A large (generally 20 Amp) electrical ON-OFF switch.

Distortion: Alteration of viewed images caused by variations in glass flatness or inhomogeneous portions within the glass. An inherent characteristic of heat-treated glass.

Distributed Audio System: A professionally installed system that allows occupants to play and control audio from a central source in at least three rooms in the home The system should include at a minimum a distribution amplifier, room controls and in-wall, on-wall or in-ceiling speakers.

Dolly Varden Siding: Beveled wood siding which is rabbeted on the bottom edge.

Doorjamb (interior): The surrounding case into which and out of which a door closes and opens. It consists of two upright pieces, called side jambs, and a horizontal head jamb.

Dormer: An opening in a sloping roof, the framing of which projects out to form a vertical wall suitable for windows or other openings.

Double Cylinder Deadbolt: This is a deadbolt lock on a door. Double cylinder means that a key must be used on both sides of the lock. A single cylinder means that a key must be used on one side of the door while a lever of some other type is used to unlock the door on the opposite side.

Double Glass: Window or door in which two panes of glass are used with a sealed air space between. Also known as Insulating Glass.

Double-Glazing: In general, any use of two lights of glass, separated by an air space, within an opening, to improve insulation against heat transfer and/or sound transmission. In insulating glass units the air between the glass sheets is thoroughly dried and the space is sealed, eliminating possible condensation and providing superior insulating properties.

Double Hung: A window that both the upper and lower window sashes move up and down.

Double Plate: When two layers of two by four's are placed on top of studs in framing a wall.

Double Strength: In float glass, approximately 1/8" (3 mm) thick.

Double Tree: Refers usually to a precast roof deck panel poured with two fins in its underside to impart flexural rigidity.

Downspout: The metal pipe used to drain water from a roof.

Draw: The amount of progress billings on a contract that is currently available to a contractor under a contract with a fixed payment schedule.

Drawing Outline: A top view drawing of a building or roof showing only the perimeter drawn to scale.

Drawing Detail: A top view drawing of a building or roof showing the roof perimeter and indicating the projections and roof mounted equipment, drawn to scale.

Dressed and Matched (Tongued and Grooved): Boards or planks machined in such a matter that there is a groove on one edge and a corresponding tongue on the other.

Dressed Size Lumber: The dimension of lumber after shrinking from green dimension and after machining to size or pattern.

Drier Paint: Usually oil-soluble soaps of such metals as lead manganese, or cobalt, which, in small proportions, hasten the oxidation and hardening (drying) of the drying oils in paints.

Drip: (a) A member of a cornice or other horizontal exterior finish course that has a projection beyond the other parts for throwing off water. (b) A groove in the under. side of a sill or drip cap to cause water to drop off on the outer edge instead of drawing back and running down the face of the building.

Drip Cap: A molding placed on the exterior top side of a door or window frame to cause water to drip beyond the outside of the frame.

Drip Edge: A device designed to prevent water from running back or under an overhang.

Drippage: Bitumen material that drips through roof deck joints, or over the edge of a roof deck.

Driveway Approach: Driveway area between the street and the sidewalk at the front of the property. This area must be concrete as opposed to brick pavers since it must connect with the street.

Drop in Sink: Sink that is surface mounted on a counter top. The rim of the sink is visible. A sink that the rim is not visible is called an under mount sink.

"Dropping" a Stringer: In carpentry, means cutting short on the bottom of a stairs, to allow for thickness of the first tread.

Drop Siding: Usually 3⁄4 inch thick and 6 and 8 inches wide with tongued-and-grooved or shiplap edges. Often used as siding without sheathing in secondary buildings.

Dry Glazing: Also called compression glazing, a term used to describe various means of sealing monolithic and insulating glass in the supporting framing system with synthetic rubber and other elastomeric gasket materials.

Dry-In: To make a building waterproof.

Dry Seal: Accomplishment of weather seal between glass and sash by use of strips or gaskets of Neoprene, EPDM, silicone or other flexible material. A dry seal may not be completely watertight.

Dry Sheet: A ply mechanically attached to wood or gypsum decks to prevent asphalt or pitch from penetrating the deck and leaking into the building below.

Drywall: Sheetrock (gypsum board) that covers the framing and taping, coating, and finishing to make the interior walls and ceilings of a building. Drywall is also used as a verb to refer to installation process.

Drywall Construction: A type of construction in which the interior wall finish is applied in a dry condition, generally in the form of sheet materials or wood paneling as contrasted to plaster.

Drywall Hammer: A special hammer used for nailing up gypsum board. It is also known as an ax or hatchet. Edges should be smooth and the corners rounded off. The head has a convex round & checkered head.

Drywall Nail: Nails used for hanging regular drywall that is to be taped and finished later must have adequate holding power and a head design that does not cut the face paper. They must also be of the proper depth to provide exactly 1 inch penetration into the framing member. Nails commonly used are chemically-etched and are designed with a cupped head.

Duct: A cylindrical or rectangular "tube" used to move air either from exhaust or intake, and for distributing warm air from the heating plant to rooms, or air from a conditioning device or as cold air returns. The installation is referred to as "duct work".

Dumbwaiter: An elevator with a maximum footage of not more than nine sq. ft. floor area; not more than four inches headroom and a maximum capacity of 500 lbs. used for carrying materials only.

Dura Rock: Reinforced concrete sheets installed on the wall or a wood floor prior to the installation of tile. The Dura Rock will not rot or absorb water while green board or water resistant drywall will. This is a must for all wall tile and tile installed on wood floors.

Durometer: The measurement of hardness of a material. A gauge to measure the hardness of an elastomeric material.

back to top

- E -

Easement: A formal contract which allows a party to use another party's property for a specific purpose. e.g. a sewer easement might allow one party to run a sewer line through a neighbor’s property.

Eave: The part of a roof which projects out from the side wall, or the lower edge of the part of a roof that overhangs a wall.

Edge Clearance: Nominal spacing between the edge of the glass product and the bottom of the glazing pocket (channel).

Edge Grain (vertical): Edge-grain lumber has been sawed parallel to the pith of the log and approximately at right angles to the growth rings; i.e., the rings form an angle of 45 degrees or more with the surface of the piece.

Edge Metal: A term relating to brake or extruded metal around the perimeter of a roof.

EER (Energy Efficiency Ratio): Figured by dividing BTU hours by watts.

Efflorescence: The process by which water leeches soluble salts out of concrete or mortar and deposits them on the surface. Also used as the name for these deposits.

Egress: A means of exiting the home. An egress window is required in every bedroom and basement. Normally a 4' X 4' window is the minimum size required.

EIFS: Exterior Insulating and Finish System; exterior wall cladding system consisting primarily of polystyrene foam board with a textured acrylic finish that resembles plaster or stucco.

Elastomer: An elastic rubber-like substance, such as natural or synthetic rubber.

Elastomeric: Of or pertaining to any of the numerous flexible membranes that contain rubber or plastic.

Electrical Rough: Work performed by the Electrical Contractor after the plumber and heating contractor are complete with their phase of work. Normally all electrical wires and outlet, switch, and fixture boxes are installed (before insulation).

Electrical Trim: Work performed by the electrical contractor when the house is nearing completion. The electrician installs all plugs, switches, light fixtures, smoke detectors, appliance 'pig tails', and bath ventilation fans, wires the furnace, and makes up the electric house panel. The electrician does all work necessary to get the home ready for and to pass the municipal electrical final inspection.

Electrolytic Coupling: A fitting required to join copper to galvanized pipe and gasketed to prevent galvanic action. Connecting pipes of different materials may result in electrolysis.

Elevation: Drawing depicting the final look of an element such as each side of the home.

Emissivity: The measure of a surface’s ability to emit long-wave infrared radiation.

EMT (Electrical Metallic Tubing): This electrical pipe, also called thin-wall conduit, may be used for both concealed and exposed areas. It is the most common type of raceway used in single family and low rise residential and commercial buildings.

Emulsion: In roofing, a coating consisting of asphalt and fillers suspended in water.

End Dams: Internal flashing (dam) that prevents water from moving laterally within a curtain wall or window wall system.

End Lap: The amount or location of overlap at the end of a roll of roofing felts in the application.

EPDM (Ethylene Propylene Diene Monomer): A single ply membrane consisting of synthetic rubber; usually 45 or 60 mils. Application can be ballasted, fully adhered or mechanically attached.

Evaporator Coil: The part of a cooling system that absorbs heat from air in your home. Also see condensing unit.

Excavate: Dig the basement and or all areas that will need footings/foundations below ground.

Expansion Coefficient: The amount that a specific material will vary in any one dimension with a change of temperature.

Expansion Joint: A device used to permit a structure to expand or contract without breakage. In residential construction, a bituminous fiber strip used to separate blocks or units of concrete to prevent cracking due to expansion as a result of temperature changes. Also used on concrete slabs.

Exterior Glazed: Glazing infills set from the exterior of the building.

Exterior Rock Salt Accent Painting: This treatment can be applied to stucco banding, columns, window sills, etc. that has been pitted with rock salt to resemble cast stone. It is a 2-3 stage treatment. First, the material is painted with the color desired for the pitted area of the surface. It is then repainted with the color desired for the main area of the surface. This treatment makes the pitted areas stand out and really finishes the cast stone look for a fraction of the cost of cast stone. Sometimes, our clients have the banding and other faux stone trim faux painted for an even nicer, more authentic look.

Exterior Stop: The molding or bead that holds the light or panel in place when it is on the exterior side of the lite or panel.

Extrusion: An item formed by forcing a base metal (frequently aluminum) or plastic, at a malleable temperature, through a die to achieve a desired shape.

Eyebrow: A flat, normally concrete, projection which protrudes horizontally from a building wall; Eyebrows are generally located above windows.

back to top

- F -

Facade: The front of a building. Frequently, in architectural terms an artificial or decorative effort.

Face Brick: Brick made especially for exterior use with special consideration of color, texture and size, and used as a facing on a building.

Face Glazing: A system having a triangular bead of compound applied with a putty knife, after bedding, setting, and clipping the glazing infill in place on a rabetted sash.

Factory Mutual (FM): Insurance agency that has established stringent guidelines for maximum construction integrity as it relates to fire and environmental hazards. Their specifications have become industry standards.

Fascia: The flat, vertical surface immediately below the edge of a roof. It is the surface a gutter would be attached to. The term fascia can also be used to describe other flat vertical surfaces in a home.

Fasteners: A general term covering a wide variety of screws and nails, which may be used for mechanically securing various components of a building.

Faux Painting: Paint applied by an artist to a surface in a manner to match a certain pattern and color desired. Normally requires a base coat of paint with numerous other coats of other color paint to achieve the desired look. Faux painting is used on walls and many other surfaces. Almost any faux look can be accomplished.

Felt: A very general term used to describe composition of roofing ply sheets, consisting of a mat of organic or inorganic fibers unsaturated, impregnated with asphalt or coal tar pitch, or impregnated and coated with asphalt.

Fenestration: Any glass panel, window, door, curtain wall or skylight unit on the exterior of a building.

Ferrous: Refers to objects made of or partially made of iron, such as ferrous pipe.

Fillet Bead: Caulking or sealant placed in such a manner that it forms an angle between the materials being caulked.

Finish: In hardware, metal fastenings on cabinets which are usually exposed such as hinges and locks.

Finish Carpentry: The hanging of all interior doors, installation of door molding, base molding, chair rail, built in shelves, etc.

Finish Coat: The last coat applied in plastering intended as a base for further decorating or as a final decorative surface. Finish coat usually consists of calcified gypsum, lime and sometimes an aggregate. Some may require the addition of lime or sand on the job. The three basic methods of applying it are (1) trowel (2) flat and (3) spray.

Finish Grade: Any surface that has been cut to or built to the elevation indicated for that point. Surface elevation of lawn, driveway or other improved surfaces after completion of grading operations.

Fire Rated: Descriptive of materials that has been tested for use in firewalls.

Fire-Resistive: In the absence of a specific ruling by the authority having jurisdiction, applies to materials for construction not combustible in the temperatures of ordinary fires and that will withstand such fires without serious impairment of their usefulness for at least one hour.

Fire Retardant Chemical: A chemical or preparation of chemicals used to reduce flammability or to retard spread of flame.

Fire Stop: A solid, tight closure of a concealed space, placed to prevent the spread of fire and smoke through such a space. In a frame wall, this will usually consist of two by four's cross blocking between studs.

Fire Wall: Any wall built for the purpose of restricting or preventing the spread of fire in a building. Such walls of solid masonry or concrete generally sub-divide a building from the foundations to two or more feet above the plane of the roof.

Fishplate: A wood or plywood piece used to fasten the ends of two members together at a butt joint with nails or bolts. Sometimes used at the junction of opposite rafters near the ridge line.

Fish Tape (Fish Wire): Material used to advance wire through a conduit.

Flagstone (Flagging or Flags): Flat stones, from 1 to 4 inches thick, used for rustic walks, steps, floors, and the like.

Flake: A scale-like particle. To lose bond from a surface in small thin pieces. Sometimes a paint film "flakes".

Flash Point: The critical temperature at which a material will ignite.

Flashing: Weatherproof material installed between roof sheathing (or wall sheathing) and the finish materials to help keep moisture away from the sheathing. Typically, sheet metal or a similar material is used in roof and wall construction to protect a building from water seepage.

Flat Glass: A general term that describes float glass, sheet, glass, plate glass, and rolled glass.

Flat Grain: Flat-grain lumber has been sawed parallel to the pith of the log and approximately tangent to the growth rings, i.e., the rings form an angle of less than 45 degrees with the surface of the piece.

Flat Paint: An interior paint that contains a high proportion of pigment and dries to a flat or lusterless finish.

Flat Seam: A seam at the junction of sheet metal roof components that has been bent at the plane of the roof.

Flatwork: Common word for concrete floors, driveways, basements, and sidewalks.

Fleet Averaging: By using a point system, builders can show compliance with energy building requirements by using average figures for all air conditioning units in the same sub division.

Flexible Metal Conduit: Conduit similar to armored cable in appearance but does not have the pre-inserted conductors.

Float Glass: Glass formed on a bath of molten tin. The surface in contact with the tin is known as the tin surface or tin side. The top surface is known as the atmosphere surface or air side.

Floor Plan: The basic layout of building or addition, which includes placement of walls, windows and doors as well as dimensions.

Floor Plate: See Floor Plan

Flue: Large pipe through which fumes escape from a gas water heater, furnace, or fireplace. Normally these flue pipes are double walled, galvanized sheet metal pipe and sometimes referred to as a 'B Vent'. Fireplace flue pipes are normally triple walled. In addition, nothing combustible shall be within one inch from the flue pipe.

Flue Lining: Fire clay or terra-cotta pipe, round or square, usually made in all ordinary flue sizes and in 2-foot lengths, used for the inner lining of chimneys with the brick or masonry work around the outside. Flue lining in chimneys runs from about a foot below the flue connection to the top of the chimney.

Flush Glazing (Pocket Glazing): The setting of a light of glass or panel into a four-sided sash or frame opening containing a recessed "U" shaped channel without removable stops on three sides of the sash or frame and one channel with a removable stop along the fourth side.

Fly Rafters: End rafters of the gable overhang supported by roof sheathing and lookouts.

Foam Insulation: Foam insulation is injected into the exterior concrete block wall cavities not filled with concrete. Foam insulation not only offers a great insulation value, but also provides excellent sound insulation. More importantly though, it fills every cavity and void in the exterior walls eliminating places where bugs and other pest can reside and enter the home.

Folded Seam: In sheet metal work, a joint between sheets of metal wherein the edges of the sheets are crimped together and folded flat.

Footer: The concrete reinforced supporting base or groundwork of the home.

Footings: Wide pours of cement reinforced with rebar (reinforcing bar) that support foundation walls, pillars, or posts. Footings are part of the foundation and are often poured before the foundation walls.

Foot Print: See Floor Plan

Foundation: The supporting portion of a structure below the first floor construction, or below grade, including the footings.

Framer: The carpenter contractor that installs the lumber and erects the frame, flooring system, interior walls, backing, trusses, rafters, decking, installs all beams, stairs, soffits and all work related to the wood structure of the home. The framer builds the home according to the blueprints and must comply with local building codes and regulations.

Framing: Lumber used for the structural members of a building, such as studs, joists, and rafters.

French Drains: Installed below the surface of the ground to aid movement of ground water outside the home. A trench is dug in which a perforated PVC pipe is installed. The pipe is embedded in gravel and the pipe is then directed to a positive drain source. The pipe, if properly sloped, will do an excellent job draining wet areas. French drains are also known as under drains.

Frieze: In house construction a horizontal member connecting the top of the siding with the soffit of the cornice.

Frieze Bands: A plain or decorated vertical band installed below the exterior soffit and the exterior vertical veneer of the home for decorative purposes. The band is typically thicker than the adjacent wall surface and of another texture so that the band will be prominent in appearance. This term could also describe a band treatment inside the home just below the ceiling.

Frostline: The depth of frost penetration in soil. This depth varies in different parts of the country. Footings should be placed below this depth to prevent movement.

Fully-Adhered: A completely attached (adhered) roof membrane.

Fully Tempered Glass: Flat or bent glass that has been heat-treated to a high surface and/or edge compression to meet the requirements of ASTM C 1048, kind FT. Fully tempered glass, if broken, will fracture into many small pieces (dice) which are more or less cubical. Fully tempered glass is approximately four times stronger than annealed glass of the same thickness when exposed to uniform static pressure loads.

Fungi (wood): Microscopic plants that live in damp wood and cause mold, stain, and decay.

Fungicide: A chemical that is poisonous to fungi.

Furnace: A heating system that uses the principle of thermal convection. When air is heated, it rises and as the air cools it settles. Ducts are installed to carry the hot air from the top of the furnace to the rooms. Other ducts, called cold air returns, return the cooler air back to the furnace.

Furring: Strips of wood or metal applied to a wall or other surface to even it and normally to serve as a fastening base for finish material.

back to top

- G -

Gable: The end of a building as distinguished from the front or rear side. The triangular end of an exterior wall from the level of the eaves to the ridge of a double-sloped roof. In house construction, the portion of the roof above the eave line of a double-sloped roof.

Gable End: An end wall having a gable.

Gambrel Roof: A type of roof which has its slope broken by an obtuse angle, so that the lower slope is steeper than the upper slope. A double-sloped roof having two pitches.

Galvanize: To coat a metal with zinc by dipping it in molten zinc after cleaning.

Gaskets: Pre-formed shapes, such as strips, grommets, etc., of rubber or rubber-like composition, used to fill and seal a joint or opening either alone or in conjunction with a supplemental application of a sealant.

Gauge: The thickness of sheet metal and wire, etc.

Gauge Board (Spot Board): Board used to carry grout needed to patch small jobs.

General Contractor (or Prime Contractor): A contractor responsible for all facets of construction of a building or renovation.

GFI or GFCI (Ground Fault Circuit Interrupters): Special devices capable of opening a circuit when even a small amount of current is flowing through the grounding system.

GFRC: Glass Fiber Reinforced Concrete; Material used in wall systems that resembles but generally does not perform as well as concrete. Usually a thin cementitious material laminated to plywood or other lightweight backing.

Gloss Enamel: A finishing material made of varnish and sufficient pigments to provide opacity and color, but little or no pigment of low opacity. Such an enamel forms a hard coating with maximum smoothness of surface and a high degree of gloss

Gloss (paint or enamel): A paint or enamel that contains a relatively low proportion of pigment and dries to a sheen or luster.

Girder: A main beam upon which floor joists rest used to support concentrated loads at isolated points along its length, usually made of steel or wood.

Glass: A hard, brittle substance, usually transparent, made by fusing silicates under high temperatures with soda, lime, etc.

Glaze Coat: In roofing, a light, uniform mopping of bitumen on exposed felts to protect them from the weather, pending completion of the job.

Glazing: (n) A generic term used to describe an infill material such as glass, panels, etc. (v) the process of installing an infill material into a prepared opening in windows, door panels, partitions, etc.

Glazing Bead: In glazing, a strip surrounding the edge of the glass in a window or door which holds the glass in place.

Glazing Channel: In glazing, a three-sided, U-shaped sash detail into which a glass product is installed and retained.

GPM: This is a measurement that describes the number of gallons that can flow through a particular pipe or other item per minute.

Grade: Ground level or the elevation at any given point. Also the work of leveling dirt. Also the designated quality of a manufactured piece of wood.

Grade MW: Moderate Weather grade of brick for moderate resistance to freezing used, for example, in planters.

Grade NW: No Weather brick intended for use as a back-up or interior masonry.

Grade SW: Severe Weather grade of brick intended for use where high resistance to freezing is desired.

Grain: The direction, size, arrangement, appearance, or quality of the fibers in wood.

Granules: The mineral particles of a graded size, which are embedded in the asphalt coating of shingles and roofing.

Gravel: Loose fragments of rock used for surfacing built-up roofs, in sizes varying from 1/8" to 1-3/4".

Ground Fault: Ground Fault Circuit Interrupter (GFCI, GFI) - an ultra sensitive plug designed to shut off all electric current. Used in bathrooms, kitchens, exterior waterproof outlets, garage outlets, and wet areas. Has a small reset button on the plug.

Ground Iron: The plumbing drain and waste lines that are installed beneath the basement floor. Cast iron was once used, but black plastic pipe (ABS) is now widely used.

Ground: Refers to electricity's habit of seeking the shortest route to earth. Neutral wires carry it there in all circuits. An additional grounding wire or the sheathing of the metal-clad cable or conduit—protects against shock if the neutral leg is interrupted.

Grounds: Guides used around openings and at the floorline to strike off plaster. They can consist of narrow strips of wood or of wide sub-jambs at interior doorways. They provide a level plaster line for installation of casing and other trim.

Ground System: The connection of current-carrying neutral wire to the grounding terminal in the main switch, which in turn is connected to a water pipe. The neutral wire is called the ground wire.

Grounding Rod: Rod used to ground an electrical panel.

Groundwater: Water from an aquifer or subsurface water source.

Grout or Grouting: A cement mortar mixture made of such consistency (by adding water) that it will just flow into joints and cavities of masonry work to fill them solid.

Gun Consistency: Sealant formulated in a degree of viscosity suitable for application through the nozzle of a caulking gun.

Gunite: A construction material composed of cement, sand or crushed slag and water mixed together and forced through a cement gun by pneumatic pressure, used in the construction of swimming pools.

Gutter: Metal or wood trough at the eaves of a roof to carry rain water from the roof to the downspout.

Gutter Strap: Metal bands used to support the gutter.

Gusset: A flat wood, plywood, or similar type member used to provide a connection at intersection of wood members. Most commonly used at joints of wood trusses. They are fastened by nails, screws, bolts, or adhesives.

Guy Wire: A strong steel wire or cable strung from an anchor on the roof to any tall slender projection for the purpose of support.

Gypsum Plaster: Gypsum formulated to be used with the addition of sand and water for base-coat plaster.

Gypsum Board: Used to create drywall. It comes in 4’x12’ sheets that are taped and finished.

Gypsum Keene Cement: Material used to obtain a smooth finish coat of plaster, for use over gypsum plastic base coats only and in areas not subject to moisture. It is the hardest plaster.

back to top

- H -

Hardware: Metal accessories such as door knobs, towel bars, toilet paper holders, etc.

Hatch: An opening in a deck; floor or roof. The usual purpose is to provide access from inside the building.

Hawk: A flat wood or metal tool 10 inches to 14 inches square with a handle used by plasterers to carry plaster mortar or mud.

Hazard Insurance: Insurance for a building while it is under construction.

Header: Framing members over windows, doors, or other openings. A beam placed perpendicular to joists and to which joists are nailed in framing for chimney, stairway, or other opening. (b) A wood lintel.

Hearth: The inner or outer floor of a fireplace, usually made of brick, tile, or stone.

Heartwood: The wood extending from the pith to the sapwood, the cells of which no longer participate in the life processes of the tree.

Heat Recovery Units: Use waste heat from your air conditioning system to heat domestic hot water.

Heat Rough: Work performed by the Heating Contractor after the stairs and interior walls are built. This includes installing all duct work and flue pipes. Sometimes, the furnace and fireplaces are installed at this stage of construction.

Heat Strengthened Glass: Flat or bent glass that has been heat-treated to a specific surface and/or edge compression range to meet the requirements of ASTM C 1048, kind HS. Heat-strengthened glass is approximately two times as strong as annealed glass of the same thickness when exposed to uniform static pressure loads. Heat-strengthened glass is not considered safety glass and will not completely dice as will fully tempered glass.

Heat Trim: Work done by the Heating Contractor to get the home ready for the municipal Final Heat Inspection. This includes venting the hot water heater, installing all vent grills, registers, air conditioning services, turning on the furnace, installing thermostats, venting ranges and hoods, and all other heat related work.

Heel Bead: Sealant applied at the base of a channel, after setting the light or panel and before the removable stop is installed, one of its purposes being to prevent leakage past the stop.

Hermetic Seal: Vacuum seal (between panes of a double-paned window i.e. insulated glass unit or IGU). Failure of a hermetic seal causes permanent fogging between the panels of the IGU.

High-Early Cement: A portland cement sold as Type III sets up to its full strength faster than other types.

Hip: The external angle formed by the meeting of two sloping sides of a roof.

Hip Rafter: A rafter that forms the intersection of an external roof angle.

Hip Roof: A roof that rises by inclined planes from all four sides of a building.

Hoistway: A shaftway for the travel of one or more elevators.

Home Automation System: A professionally installed system that integrates the control of security, HVAC or lighting systems to enhance safety, comfort and convenience.

Home Run (Electrical): The electrical cable that carries power from the main circuit breaker panel to the first electrical box, plugs, or switch in the circuit.

Home Theater System: A professionally installed audio/video system designed to re-create cinema-like experiences in the home, including at least a five-speaker surround-sound system (at least installed or mounted on the wall or ceiling) and a video display measuring 40 inches or more.

Honeycomb: (1) Areas in a foundation wall where the aggregate (gravel) is visible. Honeycombs can be usually be remedied by applying a thin layer of grout or other cement product over the affected area. (2) Method by which concrete is poured and not puddled or vibrated, allowing the edges to have voids or holes after the forms are removed.

Hose Bib: Exterior garden hose outlet.

Hub: In plumbing, the enlarged end of a pipe which is made to provide a connection into which the end of the joining pipe will fit.

Humidifier: A device designed to increase the humidity within a room or a house by means of the discharge of water vapor. They may consist of individual room size units or larger units attached to the heating plant to condition the entire house.

HVAC: Heating Ventilation and Air Conditioning.

Hydroelectric Elevator: An elevator where liquid is pumped under pressure directly into the cylinder by a pump driven by an electric motor without an accumulator between the pump and cylinder.

back to top

- I -

I-Beam: A steel beam with a cross section resembling the letter I. It is used for long spans as basement beams or over wide wall openings, such as a double garage door, when wall and roof loads are imposed on the opening.

IIC: A new system utilized in the Federal Housing Administration recommended criteria for impact sound insulation.

Incompatibility: Descriptive of two or more materials that are not suitable to be used together.

Indemnification Clause: Provision in a contract in which one party agrees to be financially responsible for specified types of damages, claims, or losses.

Infiltration: The process by which air leaks into a building. In either case, heat loss results. To find the infiltration heating load factor (HLF), the formula to account for the extra BTU's needed to heat the infiltrated air is:
• • BTU/HR = building volume x air changes x BTU/cu.ft/hr x TD (TD is temperature difference)

INR (Impact Noise Rating): A single figure rating which provides an estimate of the impact sound insulating performance of a floor-ceiling assembly.

Inside Drain: In roofing, a drain positioned on a roof at some location other than the perimeter. It drains surface water inside the building through closed pipes to a drainage system.

Insulation Board: A rigid structural building board made of coarse wood or cane fiber in 1⁄2- and 25/32-inch thickness It can be obtained in various size sheets, in various densities, and with several treatments.

Insulating Glass Unit: Two or more lights of glass spaced apart and hermetically sealed to form a single-glazed unit with an air space between each light. (Commonly called IG units.)

Insulation: (1) Generally, any material which slows down or retards the flow or transfer of heat. Building insulation types are classified according to form as loose fill, flexible, rigid, reflective, and foamed-in-place. All types are rated according to their ability to resist heat flow (R< - Value). (2) In electrical contracting, rubber, thermoplastic, or asbestos wire covering. The thickness of insulation varies with wire size and type of material, application or other code limitations.

Insulation Fasteners: Any of several specialized mechanical fasteners designed to hold insulation down to a steel or a nailable deck.

Interior Architectural Detailing: As important or possibly more so that the architectural plans for your home. They include the plans for all of the special ceilings, niches, special trim, built ins, decorative tile details, and more for your home. They are typically prepared by the Interior Designer and Architect.

Interior Finish: Material used to cover the interior framed areas, or materials of walls and ceilings

Interior Glazed: Glazing infills set from the interior of the building.

Interlayer: In glazing, any material used to bond two lights of glass and/or plastic together to form a laminate.

Interply: Between two layers of roofing felts that have been laminated together.

IRMA: Insulated (or Inverted) Roof Membrane Assembly. In this system the roof membrane is laid directly on the roof deck, covered with extruded foam insulation and ballasted with stone, minimum of 1000 lbs. per square.

Irrigation: Exterior sprinkler system for the yard.

back to top

- J -

Jack Rafter: A rafter that spans the distance from the wall plate to a hip, or from a valley to a ridge. A rafter that spans the distance from the wall plate to a hip, or from a valley to a ridge.

Jamb: The side and head lining of a doorway, window, or other opening.

Joint: The space between the adjacent surfaces of two members or components joined and held together by nails, glue, cement, mortar, or other means.

Joint Cement: A powder that is usually mixed with water and used for joint treatment in gypsum-wallboard finish. Often called "spackle."

Joist: Wooden 2 X 8's, 10's, or 12's that run parallel to one another and support a floor or ceiling, and supported in turn by larger beams, girders, or bearing walls.

Joist Hanger: A metal U-shaped item used to support the end of a floor joist and attached with hardened nails to another bearing joist or beam.

back to top

- K -

Keene's Cement: A white finish plaster that produces an extremely durable wall. Because of its density, it excels for use in bathrooms and kitchens and is also used extensively for the finish coat in auditoriums, public buildings, and other places where walls may be subjected to unusually hard wear or abuse.

Kelvin: Thermometer scale on which a unit of measurement equals the Celsius degree.

Keyless: A plastic or porcelain light fixture that operates by a pull string. Generally found in the basement, crawl space, and attic areas.

Kick Hole: A defect frequently found in perimeter flashings arising from being stepped on or kicked. A small fracture of the base flashing in the area of the cant.

Kiln-Dried Lumber: Lumber that has been kiln dried often to a moisture content of 6 to 12 percent. Common varieties of softwood lumber, such as framing lumber are dried to a somewhat higher moisture content.

Knife Consistency: Compound formulated in a degree of firmness suitable for application with a putty knife such as used for face glazing and other sealant applications.

Knockdown: Splatter texture applied to a surface that is then troweled to achieve a particular finish. Normally used to describe finish on drywall interior walls and ceilings, porch and pool deck floor finishes, as well as a particular type of exterior wall stucco finish.

Knot: In lumber, the portion of a branch or limb of a tree that appears on the edge or face of the piece.

Kraft: A heavy, water resistant paper.

Kynar Coating: Architectural coating that is UV stable and suitable for exterior use on aluminum and other metal surfaces.

back to top

- L -

Ladder, Fixed: A ladder which is permanently attached to a building.

Laminate: Formica or other brands surface glued to a wood substrate typically for countertops.

Laminated Glass: Two or more lights of glass permanently bonded together with one or more inter-layers.

Landing: A platform between flights of stairs or at the termination of a flight of stairs.

Lap: To extend one material partially over another; the distance so extended.

Lath: A building material of wood, metal, gypsum, or insulating board that is fastened to the frame of a building to act as a plaster base.

Lattice: A framework of crossed wood or metal strips.

Lead: A malleable metal once extensively used for flashings.

Leader: See Downspout

Lean-To Roof: the sloping roof of a building addition having its rafters or supports pitched against and supported by the adjoining wall of a building.

Ledger Strip: A strip of lumber nailed along the bottom of the side of a girder on which joists rest.

Let-in Brace: Nominal 1-inch thick boards applied into notched studs diagonally.

Leveling Rod: A rod with graduated marks for measuring heights or vertical distances between given points and the line of sight of a leveling instrument. They are longer than a yardstick and are held by a surveyor in a vertical position.

Light: Space in a window sash for a single pane of glass. Also, a pane of glass.

Light Lift: Typically found where chandeliers are installed in high ceiling areas. The light lift is electrically operated and raises or lowers the light fixture for cleaning and maintenance.

Lintel: A horizontal structural member that supports the load over an opening such as a door or window.

Liquid-Applied Membrane: Generally applied to cast-in-place concrete surfaces in one or more coats to provide fully-adhered waterproof membranes that conform to all contours.

Liquated Damages: A monetary amount agreed upon by two parties to a contract prior to performance under the contract that specifies what a either party owes the other if that party defaults under the contract.

Lite: Another term for a pane of glass. Also spelled "light" in industry literature.

Live Load: Loads produced by use and occupancy of the building or other structure and do not include construction or environmental loads such as wind load, snow load, ice load, rain load, seismic load, or dead load.

Loan in Process Account: When the construction loan closes prior to start of construction the lender creates an account called the loan in process account or LIP. The total amount placed in the LIP is the agreed purchase price less any deposits or prepayments paid. The Builder is then paid from this account as construction progresses in percentage amounts according to the draw schedule provided by the lender.

Lookout: A short wood bracket or cantilever to support an overhang portion of a roof or the like, usually concealed from view

Lot: A parcel of ground with boundaries determined by the county.

Loose Laid: In roofing, a membrane "laid loosely", i.e., not adhered, over a roof deck or Burm.

Louver: An opening with a series of horizontal slats so an ranged as to permit ventilation but to exclude rain, sunlight, or vision. See also Attic ventilators.

Lumber: The product of the sawmill and planing mill not further manufactured other than by sawing, resawing, and passing lengthwise through a standard planing machine, crosscutting to length, and matching.

back to top

- M -

Male: Any part, such as a bolt, designed to fit into another (female) part. External threads are male.

Mansard Roof: A roof that rises by inclined planes from all four sides of a building. The sloping roofs on all four sides have two pitches, the lower pitch usually very steep and the upper pitch less steep.

Mantel: The shelf above a fireplace. Also used in referring to the decorative trim around a fireplace opening.

Mason's Hammer (or Bricklayer's Hammer): Tool shaped like a chisel to trim brick or stone.

Mastic: Heavy consistency compound that may remain adhesive and pliable with age. Is typically a waterproof compound applied to exterior walls and roof surfaces.

Masonry: Stone, brick, concrete, hollow-tile, concrete block, gypsum block, or other similar building units or materials or a combination of the same, bonded together with mortar to form a wall, pier, buttress, or similar mass

Mastic: A pasty material used as a cement (as for setting tile) or a protective coating (as for thermal insulation or waterproofing)

Matched Lumber: Lumber that is dressed and shaped on one edge in a grooved pattern and on the other in a tongued pattern.

Maximum Occupancy Load: The maximum number of people permitted in a room and is measured per foot for each width of exit door. The maximum is 50 per foot of exit.

Medallions: Normally adhered to a wall or ceiling. They can be plaster, stone, precast stone, etc. They are typically decorative in nature.

Melt Point: The temperature at which the solid asphalt becomes a liquid.

Membrane: A generic term relating to a variety of sheet goods used for certain built-up roofing repairs and application.

Metal Edge: Brake metal or metal extrusions that are secured at the perimeter of the roof to form a weather-tight seal.

Metal Lath: Sheets of metal that are slit and drawn out to form openings. Used as a plaster base for walls and ceilings and as reinforcing over other forms of plaster base.

Migration: Spreading or creeping of a constituent of a compound onto/into adjacent surfaces. See bleeding.

Mil Thickness: Measurement used to determine thickness of a coating. 1 mil = .001 inch (1/1000).

Millwork: Generally all building materials made of finished wood and manufactured in millwork plants and planing mills are included under the term "millwork." It includes such items as inside and outside doors, window and doorframes, blinds, porchwork, mantels, panelwork, stairways, moldings, and interior trim. It normally does not include flooring, ceiling, or siding.

Mineral Spirits: A by-product of petroleum, clear in color, a solvent for asphalt coatings.

Miter Joint: The joint of two pieces at an angle that bisects the joining angle. For example, the miter joint at the side and head casing at a door opening is made at a 45 degree angle.

Mock-Up Testing: Controlled air, water and structural performance testing of existing or new glazing systems.

Modulus: Stress at a given strain. Also tensile strength at a given elongation.

Moisture Content of Wood: Weight of the water contained in the wood, usually expressed as a percentage of the weight of the ovendry wood.

Molding: A wood strip having an engraved, decorative surface.

Monitor: A large structure rising above the surrounding roof planes, designed to give light and/or ventilation to the building interior.

Mopping: In roofing, a layer of hot bitumen mopped between plies of roofing felt. Full mopping is the application of bitumen by mopping in such a manner that the surface being mopped is entirely coated with a reasonably uniform coating. Spot Mopping is the procedure of applying hot bitumen in a random fashion of small daubs, as compared to full mopping. Sprinkle mopping is a special application of installing insulation to the decks. It is done by dipping a roof mop into hot bitumen and sprinkling the material onto the deck. Strip Mopping is the application of bitumen in parallel bands.

Mortar: A mixture of cement (or lime) with sand and water used in masonry work.

Mortar Types: Type M is suitable for general use and is recommended specifically for masonry below grade and in contact with earth, such as foundations, retaining walls and walks. Type M is the strongest type. Type S is suitable for general use and is recommended where high resistance to lateral forces is required. Type N is suitable for general use in exposed masonry above grade and is recommended specifically for exterior walls subject to severe exposures. Type 0 is recommended for load-bearing walls of solid units where the compressive stresses do not exceed 100 lbs. per square inch and the masonry wall not be subjected to freezing and thawing in the presence of excessive moisture.

Mortgagee: The lender who makes the mortgage loan.

Mortise: A slot cut into a board, plank, or timber, usually edgewise, to receive tenon of another board, plank, or timber to form a joint.

Motor Court: Driveway area in front of garage.

Mud Cracks: Cracks developing from the normal shrinkage of an emulsion coating when applied too heavily.

Mullion: A vertical bar or divider in the frame between windows, doors, or other openings that supports and holds such items as panels, glass, sash, or sections of a curtain wall.

Muntins: Horizontal or vertical bars that divide the sash frame into smaller lights of glass. Muntins are smaller in dimensions and weight than mullions.

back to top

- N -

Nailer: A piece of lumber secured to non-nailable decks and walls by bolts or other means, which provides a suitable backing onto which roof components may be mechanically fastened.

Natural Finish: A transparent finish that does not seriously alter the original color or grain of the natural wood. Natural finishes are usually provided by sealers, oils, varnishes, water-repellent preservatives, and other similar materials.

Neat Plaster: A base coat plaster that does not contain aggregates and is used where the addition of aggregates on the job is desired.

Neoprene: A synthetic rubber having physical properties closely resembling those of natural rubber. It is made by polymerizing chloroprenes, and the latter is produced from acetylene and hydrogen chloride.

Newel: A post to which the end of a stair railing or balustrade is fastened. Also, any post to which a railing or balustrade is fastened.

NM: A type of Romex cable (nonmetallic sheathed cable that contains several conductors). The cable, which is flame-retardant, is limited to use in dry locations only and cannot be exposed to excessive moisture.

NMC (Non Metallic Conduit): A type of Romex cable (nonmetallic sheathed cable that contains several conductors). NMC may be used in damp or corrosive locations as well as dry areas.

Nonbearing Wall: A wall supporting no load other than its own weight.

Non-Destructive: A phrase describing a method of examining the interior of a component whereby no damage is done to the component itself.

Non-Drying (Non-Curing): A sealant that does not set up or cure. See Butyl.

Non-Sag: A sealant formulation having a consistency that will permit application in vertical joints without appreciable sagging or slumping. A performance characteristic that allows the sealant to be installed in a sloped or vertical joint application without appreciable sagging or slumping.

Non-Skinning: Descriptive of a product that does not form a surface skin.

Non-Staining: Characteristic of a compound that will not stain a surface.

Nosing: The projecting edge of a molding or drip. Usually applied to the projecting molding on the edge of a stair tread.

Notch: A crosswise rabbet at the end of a board.

Nozzle: The tubular tip of a caulking gun through which the compound is extruded.

Nuclear Meter: A device used to detect moisture by measuring slowed, deflected neutrons.

back to top

- O -

O.C. (On Center): A measurement term meaning a certain distance between like materials. Studs rafters, joists, and the like in a building placed at 16 inches O.C. will be laid out so that there is 16 inches from the center of one stud to the center of the next.

O. G. (or ogee): A molding with a profile in the form of a letter S; having the outline of a reversed curve. A molding with a profile in the form of a letter S; having the outline of a reversed curve.

Ohmmeter: In electrical contracting, a device to measure the resistance across a load. They are never used on a live circuit. It is used to track down broken wires.

Ohm's Law: States that, in a given electrical circuit, the amount at current in amps is equal to the pressure in volts divided by the resistance in ohms. The formula is: I (Current) = V voltage or V = I x R R resistance or R = V/I

Oil-Canning: The term describing distortion of thin-gauge metal panels which are fastened in a manner restricting normal thermal movement.

Organic: A term designating any chemical compound which contains carbon and hydrogen.

Outrigger: An extension of a rafter beyond the wall line. Usually a smaller member nailed to a larger rafter to form a cornice or roof overhang.

Overhang: That part of the roof structure which extends horizontally beyond the vertical plane of the exterior walls of a building.

Oxidize: To combine with oxygen in the air.

back to top

- P -

Paint: A combination of pigments with suitable thinners or oils to provide decorative and protective coatings.

Panel: In house construction, a thin flat piece of wood, plywood, or similar material, framed by stiles and rails as in a door or fitted into grooves of thicker material with molded edges for decorative wall treatment.

Parapet Wall: A low wall around the perimeter of a roof deck.

Parge Coat: A thin application of plaster for coating a wall.

Parking Strip: The area in front of a building between the sidewalk and the street usually landscaped with grass. The parking strip serves as a buffer between the road and pedestrians walking on the sidewalk.

Parting Stop or Strip: A small wood piece used in the side and head jambs of double-hung windows to separate upper and lower sash.

Partition: A wall that subdivides spaces within any story of a building.

Patterned Glass: On type of rolled glass having a pattern impressed on one or both sides. Used extensively for light control, bath enclosures and decorative glazing. Sometimes call "rolled", "figured", or "obscure" glass.

Paver Stones: Usually pre-cast concrete slabs use